Drill Master 69652 Operations Instructions download pdf (Page 15)

SECTION ON/OFF

The Console has three Section On/Off toggle switches on top

of the Console. The toggle switches turn Drill Sections ON

and OFF directly and also signal the Console which Sections

are on or off.

Sections are NOT under software control and CAN NOT be

turned on and off with VRA control.

When in the RATE mode then the Number Icons (1, 2, 3) will

indicate which Sections are turned on. However, if a Section

has zero Rows/Section then the icon for that Section will

remain off (except during calibration) even if the toggle

switch is accidentally turned on.

If using a multi-section adaptor module to control more

than one section, the output of the switches is used by the

module to determine if a flow signal should be present. If the

module senses a Section On signal, a Flow signal is expected

from the corresponding section.

NOTE: To avoid having unused sections cause a No Flow

or Emergency Stop condition, the unused section switches

must remain off.

Turning all used Sections off will not select the Hold mode.

Distance will continue to operate but Area counters will not

change since the Width is zero with all used Sections off.

When all used Sections are turned off the Console will stop

accumulating Weight even if a Seed Shaft (flow) signal is

present.

Turning all used Sections off may or may not turn the PWM

Valve off (stop hydraulic flow) depending on the setting

of the AUTO SHUT OFF cal factor (see AUTO SHUT OFF

information on page 21).

Turning all used Sections off will disable Automatic Control

(even if PWM output continues).

WIRELESS INPUT

An optional Wireless Remote Module can be added to

provide Wireless Run, Hold and +/- functions.

Operation (cont)

Console Switches and Inputs

BIN LEVEL SENSOR INPUT

When the Bin Level Sensor input goes low, the Seed Bin

is near empty and the Console will begin to flash LL

(alternate with normal display data).

When used with a single Section Drill (single Seed Bin) the Bin

Level Sensor drives the Bin Level Sensor input directly.

When used with a three Section Drill, then an external

Module is used to multiplex up to three Bin Level Sensors

(three separate Seed Bins). When any one of the three Bin

Level Sensor inputs are low, the Module will signal the

console flash LL.

SEED SIGNAL Flow INPUT

When used with a single Section Drill (single Seed Bin) there

is only one Seed Meter drive shaft. The Sensor on that shaft

drives the Seed Signal input directly.

When used with a three Section Drill there are three Bins and

three Seed Meter drive shafts and they can be turned on and

off independently. In that case an external Module is used

to select one of the three possible Seed signals. The Module

will normally use the Seed Signal from Section 1 but if that

Section is turned off then the Module will automatically

select one of the other two Seed Signals (which ever is still

running).

It should be noted that Seed Signal (flow) input does not

count Seeds directly and blocked Seed tubes or empty bins

(no Seeds) will not be detected.

NOTE: The Low Bin Not Low input is used to provide a

warning that the Seed Bin is empty.

PWM OUTPUT

The Console is designed to drive a Proportional Flow Control

Valve. The PWM duty cycle will vary from the Min PWM to

Max PWM calibrate values.

The Proportional Valve controls the hydraulic flow in 1 to 3

Hydraulic Motors so it can be used with 1 to 3 Section Grain

Drills or Fertilizer Applicators.

NOTE: All hydraulic Motors MUST BE plumbed in series so

they all rotate at the same speed so all Sections dispense

the same amount of seed per revolution of the Seed drive

shaft.

CrustBuster

DrillMaster Quick Start Guide

346-001150 Pg 15 Revised 11/2010

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 34 35

Comments to this Manuals

No comments

Drill Master 69652 Operations Instructions Page 15

Comments to this Manuals

Related products and manuals for Power drills Drill Master 69652